Z Motorcycle. Service Manual. All rights reserved. No parts of this publication may be reproduced, stored in a retrieval system, 25, (K) To protect the environment in which we all live, Kawasaki has incorporated crankcase emis-. top > Search for Owner’s Manual (Motorcycle). How to use this service. , , , , , , , , , , , , , . KAWASAKI Z REPAIR MANUAL DOWNLOAD This is the COMPLETE factory service workshop repair manual printed for the KAWASAKI Z

Author: Vudojin Kajinos
Country: Mayotte
Language: English (Spanish)
Genre: Medical
Published (Last): 10 March 2009
Pages: 82
PDF File Size: 17.55 Mb
ePub File Size: 8.90 Mb
ISBN: 708-7-71475-291-2
Downloads: 10515
Price: Free* [*Free Regsitration Required]
Uploader: Vokazahn

Engine Stop Switch d. Follow the specific tightening sequence.

Owner’s Manuals & Service Manuals | Kawasaki Vehicles

Fuel tank breather hose right, blue 3. Joint Connector A 7. Main Fuse 30A 3.

Replace the caliper if the cylinder and piston are badly scores or rusty. Starter Motor Clutch Inspection If the separator has any cracks kawaxaki damage, replace it with a new one. Connecting rod twist – – – TIR 0.

Download Manual: 2003 Kawasaki Z1000 — Owner’s Manual

How To Use This Manual Be alert for problems and non-scheduled correctly followed, could result in per- maintenance. If the fan rotates, inspect the fan switch. Read the owers at the average of the maximum and minimum indications. Gaskets, O rings, Ownefs seals, Grease seals, circlips or cotter pins must be replaced with new ones whenever disassembled. The push rod does not return to its original position once it moves out to take up camshaft owner slack.


If the corrugated fins [A] are deformed, carefully straighten them. Throttle Sensor Resistance Connections: Radiator fan switch lead Run the lead through into the water hose. The initial maintenance is vitally important and must not be neglected.

Stick coil trouble Inspect see chapter Inlet air pressure sensor manuaal Fuel Pump Relay for fuel j. ECU Fuse 15A f. Year of initial registration: Joint Connector B Australia Light LED Run the lead end till it touches the boss of the crankcase. Page Apply silicone sealant [A] to the crankshaft sensor lead grommet and crankcase halves mating surface on the front and rear sides of the crankshaft sensor cover mount. Fuel Pressure idling Standard: Clamp Ignition switch connector HIS-El should be 24mm 0.

OWNER’S MANUAL | Search for Owner’s Manual (Motorcycle)

Download Model Information – Kawasaki. Wait until the mufflers cool down. Suspend an ac- curate thermometer [B] in the water so that the heat sen- sitive portions [C] are located in almost the same depth. If the spring of either fork leg kasasaki shorter than the service limit, it must be replaced.

Overall height 1 mm Here you can read or download chevrolet suburban repair manual free directly from the. Place a strip on each journal parallel to the camshaft installed in the correct position.

Fuel pressure too low or too high Inspect see chapter 3. CAUTION To avoid damaging the electrical connections in- side the switch, be sure that the switch body does not turn during adjustment. Replace the O-rigs of the indicators.


If any wiring is poor, z100 the damaged wiring. Yamaha’s FZ1 as the first Japanese motorcycle to give naked Such a shock to the pump can damage it. Measure the clearance when engine is cold. If the engine cannot be started, the self-diagnosis system does not detect dynamic condi- tion of the camshaft position sensor.

Special tools, gauges, and testers that are necessary when servicing Kawasaki Motorcycles are introduced by the Special Tool Manual. Joint Connector B N.

Production model years and Motorcycle Kawasaki Z Owner’s Manual pages. Torque – Gear Positioning Lever Bolt: Pilot Screw Adjuster, C: If the frame is bent, dented, cracked, or warped, replace it. Gasket Before Frame No. An imbalance of less than 10 grams 0.

Kawasaki Z1000 Service Manual

Therefore, replace the sealed battery only on a kkawasaki which was originally equipped with the sealed battery. If it is damaged, replace it. Turn the ignition switch OFF.